How to set up a Fishing Rod for Lake Fishing: Handy Tips For You

Are you planning to do lake fishing?It’s always necessary for you to assemble all the equipment you are going to use. A fishing rod is one of the major items you will need. Are you frustrated about setting up your fishing rod? This article will enlighten you on how you achieve it.

Firstly, it is a pre-requisite that you are combed with the necessary information about fishing rods. It will thrill you to know the items you are dealing with in and out. This will even make your work easier during the setup process.

The equipment required in the making of fishing rods come in different types and sizes. Make a decision about the specifications you shall need. Take a notebook and write jot them down.Don’t worry about where to find the tools as you can simply get them from your local fishing shops.

What are the items used to make a fishing rod?

As a fisherman, you should have a box that will store all your tools for fishing. By so doing, your work will be made easier.This box should have the basic items listed below.

A-Rod

A fishing rod is a long flexible slender pole. It is usually made of graphite which is long lasting or the traditional bamboo. A good one should not be longer than your own height.

Reel

It is attached to the rod. This enables you to wine your line and catch your fish. Moreover, a reel is light in weight and simple to fix. A new reel usually comes with one or two rounds of fishing line.

A Fishing Line

This refers to a string.You may require to have a stock of strings as they sometimes break. Choose a fishing line according to their weight and strength. It's important to note that your reel should have a minimum of 100 yards of fishing line.

A Swivel

A swivel has a loop attached to its ends for holding baits. It is a tool that connects the bait to your line. It allows your bait to swing freely and don’t affect your fishing line.

Hooks

A keen fisherman should have a pair of assorted hooks. This makes catching of different sizes of fish easier. A hook can poke a fish either in the mouth or the body. Hooks come in different types and sizes. There are various types to use which include;treble, double and single circle. Choose the sizes as per your needs.

Floaters

They are used to keep your bait closer to the surface. When a fish eats your bait, the floater will sink. This will be a signal that a fish has been caught. White and red plastic ones are the most preferred ones because they are easy to use.

Sliders

They ensure that the fish don’t feel the weight when catching the bait. The fishing line passes through the slider as soon as the fish eats the bait. Your fish will then be caught.fi

Bait 

Live baits are commonly used. They are tied to the far end of your line for attracting fish.Nightcrawlers, small freshwater fish,worms, and marshmallows are some of the baits used. The types of baits used may vary according to the types of fish you might want to catch.

Also read: How Does A Fish Finder Transducer Work? Important Guide

How do you setup a Fishing Rod?

As a fisherman, you will feel fulfilled when using a fishing rod that you made yourself. These simple steps will guide you on the basics to make your own fishing rod.

Step 1

Firstly,take the fishing line and run it through the positioned holes on your rod. These holes are the small loops or rings hanging along the lower side of the rod. It’s always advisable to start from the farthest end and work your way towards the reel.

Step 2

Open the reel by removing the covering cap. Look out for the spool of the bail on the spinning reel and open it.  Tie the line on it with a little knot. Tie another knot over the first one. Finally, pull the two knots tight against the reel.

Step 3

Close out the bail. You can do this by lowering the wire arm as far as it may go.This will make the line locked in one place. Make sure that the line comes out done. If not, you can uplift the bail and do the knot once again.

Step 4

Start swirling the fishing line into the spool.  Wrap the line in the same direction that your bail is rotating towards to.Continue doing this until when there is about an eighth of an inch gap between the outside edge of the spool and the line.

Step 5

Remember you had opened the reel and you need to close it. The reel now has the new line threaded on it. Pass the remaining line through the hole on the cover of the reed. Safely put the covering cap on the reel twisting it in a clockwise direction.

Step 6

Cut the line just a few feet from the tip of the rod. Be careful not to cut the hanging line under the rod’s line guides.Then tie the line onto a snap swivel with a strong knot.

Step 7

Take your hook and leader and connect them to the other hand of the swivel. A good leader should be around 18 inches.

Step 8

Take a sinker or floater and attach it to the slider.A nice sinker should be light in weight and be able to hold the bait down.  This helps to stay in place and not be moved by the strong currents.

Step 9

Finally, decide on the type of bait you will use. Take your bait and put it on the hook. You now ready to go into the water and start your fishing adventure.

Final Thoughts

In conclusion, making a fishing rod is easy as long as you follow all the necessary steps.Having your own customized rod ensures all your needs and goals are met. This is a great achievement any fisherman can ever look forward to.

Click Here to Leave a Comment Below 0 comments

Leave a Reply: